No-Clean Leaded

Download Technical Data Sheet
670I: Robust Paste provides good stencil life & excellent wettability.
691A: Designed for pin probability, soft residues spread from joints.

No-Clean Solder Flux

Download Technical Data Sheet
380: Slightly higher solids. Excellent activity with minimum rosin.
392-35: Excellent wetting and fluxing. Halogen free low solids organic flux.

No-Clean Wire Solder

Download Technical Data Sheet
NC600: Type RMA but wets and spreads like an "RA". Light Opaque reisdues. Minimal spattering.

Water-Soluble Wire Solder & Solid Wire No-Core

Download Technical Data Sheet
WS700: Delta Water-Soluble Wire Solder. Ease of cleaning flux residues with hot DI water.Meets J-STD-004/J-STD-006.

Q-Pearl BGA Solder Spheres

Qualitek manufactures Q-Pearls using a new technology that assures exact alloy composition, consistent and accurate diameters and highly spherical shapes of the spheres.All spheres are made from pure metals combines to provide required alloy composition according to J-STD-006 specification or customer specific. After forming the spheres are classified for size by a precise and non-abrasive sorting process. The diameters of the spheres are monitored and controlled within 0.001" +/- 0.0005" tolerance. Sphere size distribution is measured precisely by a sophisticated image analysis system connected to scanning Electron Microscope (SEM). To determine sphericity, sphere diameter is measured in 16 directions ina fraction of a second.

Tip Tinner

Temporary Solder Masks

Ceasolder
Peelable Solder Mask

Ceasolder is high temperature resistant rubber latex. It is used to temporarily mask metal surfaces from molten solder during a wave soldering process. It can be applied directly from the applicator bottle and/or dispensing through pneumatic dispenser.

QUALITEK 191A 191B 191C Thermometers

• Fast, accurate, tip temperature measurements using a fine CA wire sensor (dia 0.2mm).
• The sensors metal alloy coating resists corrosion and oxidation.
• May be used to check solder pot and the temperature of other solvent with a probe.
• The 191C has self-check function to easily check the accuracy of the unit.

Qualitek 218 ULTRASONIC CLEANERS

• Highly efficient ultrasonic wave cleans and removes smudges, dirt, grease and carbon residues.
• Advanced digital time controlled function.
• Thoroughly cleanses dirt, grease and carbon residues.
• Use to clean components that need to be electroplated before or after processing, for components of timepieces, hardware and mechanical components, jewelry, eyeglasses, spectacle frame, glassware silicon and semi conductor chips.

Qualitek 228 , 228A, 228B, 228F MAGNIFYING LAMP ESD

• Magnification with light source enhances visibility.
• Lighting is stable and reliable without flash or glare.
• Wide variety of magnification levels.
• Designed for electronic engineering to view micro or mini components and densely fitted circuit boards and for medical personal.

QUICK192 Soldering Tester

• Measures tip temperature, leak voltage and ground resistance accurately.
• Resistance to drift and temperature changes. Ensuring highly reliable measurements detected by a highly precise micro-computer.
• Meets MIL-STD-2000.

Qualitek 982B Dispenser

• The dispense function and material quantity is controlled by a timer.
• The amount of fluid or gel dispensed may be changed as desired by adjusting the air pressure, and choosing an appropriate needle.
• Materials that may be dispensed include: red gel, yellow gel, epoxy resin, tin solution, silica gel, soldering fluids. Other materials with similar viscosity may also be dispensed.

QUICK 201B ESD DESOLDERING TOOL

• The Quick 201B ESD desoldering tool is safe by design. It prevents PCBs from being damaged by static electricity and currents.
• Equipped with a powerful built-in vacuum pump imported from Japan.
• Closed loop temperature cortrol for heating the system, precisely.
• 36V power supply is safe and reliable.
• LED digital display, one touch button temperature control. Auto idle is an available option.
• Digital temperature calibration.
• Nozzles and heater are specially designed so that the melting solder can be absorbed into the filter without frequent maintenance increasing efficiency.
• The vacuum hose is heat resistant to protect it from the hot soldering iron.

Qualitek 850 SERIES REWORK STATIONS

• Qualitek 850 ESD - (Standard Design) • Qualitek 850A+ ESD - (Thermostat) • Qualitek 850AD ESD - (With Air Meter) • Qualitek 850 ESD (Qualitek 850B ESD) • Qualitek 850+ESD (Same as thermostat Qualitek 850 ESD • Qualitek 850D ESD (Thermostat, digital display) • BETTER 850 ESD (Simpler design, less cost)

QUICK 936 ESD - CE Approved

• Imported creamic heater with extended, service life.
• Separate design of handle and station.

QUALITEK 303 LEAD FREE SOLDERING STATION

• The temperature sensor is set on the front surface of the soldering tip, so it can check and control the temperature instantaneously.
• Large LDC screen design, enhances visibility of important parameters that may be seen clearly and calibrated accurately.
• Up to 64 units may be connected to the same computer simultaneously monitoring and managing the data in real-time, greatly improving the work efficiency and soldering quality.

QUALITEK GT33Q LEAD FREE SOLDERING STATION

• It's Efficient - A wide variety of tips are available to fit the soldering application.
• Auto compensation power to tip size.
• Auto idle prolongs the life of the soldering tips.
• Reaches a temperature of 300°C/570°F within 20 seconds.
• It's Economical - Priced lower than competitive models.
• New tip design reduces operating cost.
• It's Intelligent - calculates and matches power to tip size. • Idle mode reduces heat when iron is not in use. Unit will idle after 20 minutes and completely shut down when not in use for 40 minutes.
• The tip temperature can be password protected ensuring a consisten soldering temperature.

QUICK 203/H ESD - 204/H ESD - CE Approved

• Will reach 300°C from room temperature in 20 seconds.
• Effectively avoids negative impact by cold soldering.
• Relatively lower temperature will largely prolong the life of soldering tips.
• Temperature will lower to 200°C when not in use for 20 minutes and auto idle mode is energy-efficient.
• The tip temperature can be password protected ensuring a consistent soldering temperature.
• Tip design reduces operating cost.

QUALITEK IR 2015 INFRARED REWORK AND PRECISE PLACEMENT STATION

• Utilizes micro-processor controls and infrared sensor technology to do soldering and desoldering to surface mounted components safely and accurately.
• Soldering and desoldering functions are monitored under a non-contact infrared sensor achieving the optimum PCB temperature.
• The reflow soldering process is controlled by a looped circuit that ensures a precise temperature window and even heat distribution.
• Adjustable aperture protects the adjacent components from being heated.
• Will accommodate PCB’s with large thermal capacity and other high temperature situations like lead free soldering.

QUALITEK BGA 2005 REWORK STATION

• Utilizes Micro-processor and infrared sensor technology to solder and desolder surface mount components safely and accurately. It combines the features of QUALITEK IR2005 Infrared Rework Station and QUALITEK PL2005 Precision Placement System.
• Soldering and desoldering processes are under the monitoring of non-contact infrared sensors to get the optimum and reproductive PCB temperature.
• Controlling reflow soldering by looped circuit ensures a precise temperature window, even heat distribution and suitable peak value of temperature.
• The adjustable aperture can protect the adjacent components (which is sensitive to the temperature) on the PCB from being heated. Nozzles are not required.
• A reflow process camera is utilized to view the melting situation of solder materials during the soldering and desoldering process.
• It can withstand PCB’s with a large thermal capacity and other high temperature situation such as lead free soldering.

QUALITEK BGA 2100 REWORK STATION

• Qualitek BGA 2100 Rework Station adopts microprocessor control to solder and de-solder the surface mount components safely and accurately. Quicksoft software is utilized to control, record and save the technical process. This high level of control meets the demands of modern electronic component repair with a user friendly sophisticated machine.
• Qualitek BGA 2100 Rework System adopts hot airflow technology and closed-loop principles, integrating the bottom infrared preheater with the top and bottom hot air heaters. The soldering process is optimally controlled by having up to 5000w of heating power. The variable hot air flow control of both the top and bottom heaters provide a controlled rate of temperature rise, even heat distribution and minimal temperature differences.
• The 2100 has an integrated thermocouple K-type sensor system. The K-sensors can be directly attached to the components and board where critical temperature control is essential. This closed loop feedback allows you to analyze the temperature curve, peak temperature, proportion of temperature rise and change in heating process. This allows faster process setup and prevents overheating and damaged components.
• An optical aligning system incorporated in the heating area provides fast, precise adjustments. This system can process up to a 60 x 60mm component on a 600 x 500mm maximum board size. The camera is controlled with a precision motor so no manual adjustments are necessary. The system also incorporates image focusing, zoom in and out and component pick up.
• The re-work board is aligned using a joy stick, which moves the board on the X, Y & Z axis. This uses a linear precision motor for accurate reliable adjustments. All adjustments are saved in the program for fast repeatable results.
• The Qualitek BGA 2100 has top and bottom cooling with adjustable air flow and uses triple side cooling at the same time for gradual board and BGA cool down. The side cooling air flow can be adjusted separately from the top and bottom for different board demands.
• There are a variety of nozzles, pick up nozzles and board support fixtures available to meet the needs of the application.